2. Connect to 100 psi maximum shop air.
3. Keep safety bar in position at all times - except
when lowering.
4. Keep hands and tools from under carriage.
5. Do not mount table when in elevated position.
6. Do not ride vehicle onto lift.
7. Lift must be in the lowered position when moving.
8. Only trained persons should operate Air Lift.
9. The working area should be sufficiently lit.
10. Foot controller should be at least 3 feet away from
Air Lift during raising and lowering operation.
11. Recommended for indoor use only.
HANDY 10740 AIR LIFT INSTRUCTIONS
UNPACKING AND SET-UP HANDY MOTORCYCLE LIFT 10740
1. Open carton, then remove ramp, and shipping boards.
2. CAREFULLY TURN TABLE UPRIGHT INTO OPERATING POSTION BEFORE REMOVING SHIPPING CABLE RESTRAINT FROM SCISSOR MECHANISM.
3. Connect foot-operated air valve to 100 psi air supply. The lift may be damaged and/or personal injury may result if the pressure exceeds the maximum 100 psi rating.
4. Stand clear of lift table and depress the UP side of foot valve to raise table.
5. To lower table, lift detent bar from safety latch and lower to next position or to floor.
6. Insert ramp mounting pins into holes at either end of table to mount ramp.
NOTE: If cycle vise is being installed, ramp must be mounted opposite the cycle vise.
HANDY 10740 AIR LIFT OPERATION
1. Loads must be centered on table at all times.
2. Loads must be firmly positioned and secured on table at all times.
3. All moving parts have been lubricated at the factory and should be re-lubricated every 6 months to prevent galling. Grease zerks are located at each end of frame pivot shaft and at top ends of inside frame assembly.
4. Lightly oil cylinder rod when it becomes dry.
5. Squirt some oil through air bleed hole in plate end of cylinder to lubricate piston and its seal every
6 months.
6. Pivot shaft set screws should be checked frequently to be sure they are tight. These are located at the top end of the inside frame assembly.
OTHER OPTIONS AVAILABLE
Separate installation instructions included with each option.
PART # DESCRIPTION
14476 CV-17 CYCLE VISE – Vise with removable wheel stop built into vise
10730 8” SIDE EXTENSIONS (2) – Expands width of lift from 24” to 40”
10728 12” SIDE EXTENSIONS (2) – Expands width of lift from 24” to 48” includes stabilizer bar
16011 13” FRONT EXTENSIONS – Extends lift top to 93” for longer wheel base motorcycles
15566 RAMP END EXTENSION – Attaches to end of lift ramp for a more gradual incline to prevent bigger bikes from dragging bottom.
10737 SNOWMOBILE WING KIT – Used when lifting snowmobiles
14169 TRIKE EXTENSION – Used for 3 wheeled vehicles
16355 CE FOOT PEDAL – Covered foot pedal
10732 LIFT DOLLY – Helps move lift while in down position
15833 RED HANDY TIE-DOWNS – 1 pair – Secure your equipment on our lift with 1” x 6’ straps
16010 TOOL TRAY – Keeps tools organized and Handy
HANDY 10740 MOTORCYCLE LIFT REPLACEMENT PARTS
PART NO. DESCRIPTION QTY/UNIT PART NO. DESCRIPTION QTY/UNIT
10819 Detent Clip 1 11250 Screw ¾-10 x 1¾ 1
11008 Frame/Cylinder Pivot Shaft 1 11251 ½ -13 Hex Nut 4
11052 Top Assembly 1 11252 Cam Bearing Retaining Ring 2
11167 Cylinder Assy & End Plate (Gray) 1 11253 Wheel Retaining Ring 4
11071 Cylinder Shaft Assembly (Gray) 1 11254 Frame Shaft Retaining Ring 2
14381 Valve Hose w/fittings 1 11255 Lock washer - ¾” 1
11123 Ramp Assembly (Gray) 1 11304 Cylinder Shaft Bushing 1
12937 Foot Valve Assembly (complete) 1 11305 Cylinder Shaft Seal 1
12887 Valve Stem Assembly 1 11306 Piston Seal 1
11177 Detent Bar 1 11308 Piston 1
11179 Frame Pivot Shaft 1 11315 Cam Roller Bearing 4
11183 Cylinder Repair Kit 1 11316 Cam Bearing Spacer 2
11248 ½ x 1¾ Clevis Pin 2 11319 Cast Wheel 2
11249 1/8 x 7/8 Cotter Pin 2 11321 Track Roller Bearing 2
HANDY LIMITED WARRANTY
Handy Industries Division of Jadeim LLC, warrants to the original purchaser of this product, all parts to be free from defects in manufacture for a period of one (1) year from date of delivery. Notice of a defective part must be received in writing at Handy Industries within one (1) year of purchase. All defective parts must be returned to Handy Industries and which, upon our examination any parts which are defective in manufacture or workmanship, will be replaced or put in good operating condition. This warranty does not apply to damage resulting from accident, improper installation, repair, operation or maintenance, negligence or neglect. THE COST OF SUCH REPLACEMENT OR REPAIR SHALL BE EXCLUSIVE REMEDY FOR ANY BREACH OF ANY WARRANTY AND HANDY INDUSTRIES SHALL NOT BE LIABLE TO ANY PERSON FOR CONSEQUENTIAL DAMAGE, OR INJURY, OR COMMERCIAL LOSS RESULTING FROM ANY BREACH OF WARRANTY. HANDY INDUSTRIES MAKES NO WARRANTY OR MERCHANTABILITY, MAKES NO WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND MAKES NO OTHER WARRANTY EXPRESSED OR IMPLIED, INCLUDING IMPLIED WARRANTY ARISING FROM THE COURSE OR DEALING OR USAGE OF THE TRADE.
Please call Clark Heintz Tools & Equipment LLC at 603-234-2612 for more information regarding the Handy Motorcycle Lift 10740 - Standard Air Lift.
